HIGH PERFORMANCE
Material Properties Database
Genuine Material
Tiered Pricing
Browse engineering and specialty plastics by grade, manufacturer and recorded properties. Selecting PEEK, PPS, PA66 or another polymer requires more than comparing resin names: reinforcement, processing, moisture and service environment can all matter. When comparing melt flow, mechanical strength and heat resistance, check the test standard, temperature, load and specimen condition. Values obtained under different conditions are not directly interchangeable. Missing data is not zero or a failure. Confirm the manufacturer’s original technical information and test the candidate under the intended conditions before making a final selection.
Material Properties (8647 Items)
Compare
Category
Model
Manufacturer
Characteristics
Compare
Category:
Properties
Grade:
HiDura™ D1X NT
Manufacturer:
low moisture absorption, good chemical resistance, dimensional stability and high impact resilience
Physical Properties
Density
1.06
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
low moisture absorption, good chemical resistance, dimensional stability and high impact resilience
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
HiDura™ D1X NT
Manufacturer:
low moisture absorption, good chemical resistance, dimensional stability and high impact resilience
Physical Properties
Density
1.06
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
low moisture absorption, good chemical resistance, dimensional stability and high impact resilience
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
HiDura™ D0M NT0821
Manufacturer:
low viscosity, lubricated, excellent flow and release, low moisture absorption, good chemical resistance, dimensional stability
Physical Properties
Density
1.06
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
low viscosity, lubricated, excellent flow and release, low moisture absorption, good chemical resistance, dimensional stability
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
QFC0AI
Manufacturer:
LNP™ THERMOCOMP™
high modulus, high impact, low dielectric constant, low moisture absorption, good dimensional stability and good chemical resistance
Physical Properties
Density
1.43
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
high modulus, high impact, low dielectric constant, low moisture absorption, good dimensional stability and good chemical resistance
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
QFC0AI
Manufacturer:
LNP™ THERMOCOMP™
high modulus, high impact, low dielectric constant, low moisture absorption, good dimensional stability and good chemical resistance
Physical Properties
Density
1.43
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
high modulus, high impact, low dielectric constant, low moisture absorption, good dimensional stability and good chemical resistance
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
PA610+ABS_RADILON MIXLOY D HSA20UK 3010 BK
Manufacturer:
RadiciGroup
UV stabilized, Heat stabilized
Physical Properties
Density
1.08
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
UV stabilized, Heat stabilized
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
RADILON MIXLOY D 32CPA100 100 NT
Manufacturer:
RadiciGroup
High viscosity, Natural colour, Good dimensional stability, Low warpage, Improved impact resistance, Very good property retention after moisture absorption
Physical Properties
Density
1.13
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
High viscosity, Natural colour, Good dimensional stability, Low warpage, Improved impact resistance, Very good property retention after moisture absorption
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
Amilan® CM1011G-30 PA6-GF30
Manufacturer:
Thermal conductivity, Spec. heat capacity, Tensile Strength, Strain at break, Flexural modulus, Charpy impact strength, Rockwell hardness, Melting temperature, Temp. of deflection under load, Coeff. of linear therm. expansion, Burning behav., Relative permittivity, Dissipation factor, Volume resistivity, Electric strength, Water absorption, Density
Physical Properties
Density
1.36
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
Thermal conductivity, Spec. heat capacity, Tensile Strength, Strain at break, Flexural modulus, Charpy impact strength, Rockwell hardness, Melting temperature, Temp. of deflection under load, Coeff. of linear therm. expansion, Burning behav., Relative permittivity, Dissipation factor, Volume resistivity, Electric strength, Water absorption, Density
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
PA6-GB30 BALTAMID 6 GK 30 natur
Manufacturer:
{'mold_shrinkage_md': '0.011 mm/mm', 'izod_impact_strength_23c': '30 / - kJ/m²', 'tensile_strength_at_break': '70 / 40 MPa', 'elongation_at_break': '8 / 12 %', 'flexural_modulus': '4000 / 2500 MPa', 'rockwell_hardness': 'R 120 / R 105', 'glow_wire_flammability_index': '650 °C', 'dtul_66psi': '190 °C', 'dtul_264psi': '95 °C', 'melting_temperature': '222 °C', 'vicat_temperature': '195 °C', 'surface_resistivity': '* / 1E11 Ohm', 'volume_resistivity': '1E15 / 1E11 Ohm*cm', 'water_absorption': '0.9 %', 'density': '1350 kg/m³'}
Physical Properties
Density
1.35
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
{'mold_shrinkage_md': '0.011 mm/mm', 'izod_impact_strength_23c': '30 / - kJ/m²', 'tensile_strength_at_break': '70 / 40 MPa', 'elongation_at_break': '8 / 12 %', 'flexural_modulus': '4000 / 2500 MPa', 'rockwell_hardness': 'R 120 / R 105', 'glow_wire_flammability_index': '650 °C', 'dtul_66psi': '190 °C', 'dtul_264psi': '95 °C', 'melting_temperature': '222 °C', 'vicat_temperature': '195 °C', 'surface_resistivity': '* / 1E11 Ohm', 'volume_resistivity': '1E15 / 1E11 Ohm*cm', 'water_absorption': '0.9 %', 'density': '1350 kg/m³'}
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
RADILON MIXLOY S HSA30 100 NT
Manufacturer:
RadiciGroup
Natural colour. Good compromise between stiffness, toughness and good property retention after moisture absorption.
Physical Properties
Density
1.08
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
Natural colour. Good compromise between stiffness, toughness and good property retention after moisture absorption.
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
PVB702BK23 (PA6+ABS)
Manufacturer:
No Characteristics
Physical Properties
Density
1.04
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
No characteristics
data
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
PVB702NT (PA6+ABS)
Manufacturer:
No Characteristics
Physical Properties
Density
1.04
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
No characteristics
data
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
HNB0270 (PA6+ABS)
Manufacturer:
High impact or impact modified, Heat stabilized or stable to heat
Physical Properties
Density
1.07
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
High impact or impact modified, Heat stabilized or stable to heat
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
RADILON MIXLOY S 32CPA100 100 NT (PA6+ABS)-MD
Manufacturer:
RadiciGroup
High viscosity injection moulding grade
Physical Properties
Density
1.14
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
High viscosity injection moulding grade
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
RADILON MIXLOY S CPA100K 100 NT (PA6+ABS)-MD10
Manufacturer:
Heat stabilized, Natural colour, Good dimensional stability, Low warpage, Improved impact resistance, Good property retention after moisture absorption
Physical Properties
Density
1.14
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
Heat stabilized, Natural colour, Good dimensional stability, Low warpage, Improved impact resistance, Good property retention after moisture absorption
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
PA6+ABS PENTALLOY BS H natural
Manufacturer:
High impact or impact modified, Heat stabilized or stable
Physical Properties
Density
1.07
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
High impact or impact modified, Heat stabilized or stable
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
LUMID HI5083A(W) (PA6+ABS)-MF8
Manufacturer:
No Characteristics
Physical Properties
Density
1.11
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
No characteristics
data
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
PA6+ABS PENTALLOY BS H black
Manufacturer:
No Characteristics
Physical Properties
Density
1.07
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
No characteristics
data
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
LOXIAMID PA6/ABS HS1 UV1 09001
Manufacturer:
No Characteristics
Physical Properties
Density
1.07
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
No characteristics
data
Recorded properties are for screening; verify source data and conditions.
Compare
Category:
Properties
Grade:
LUMID HI5006A(W) (PA6+ABS)
Manufacturer:
High impact or impact modified
Physical Properties
Density
1.06
g/cm³
Thermal Properties
Melting Point
- °C
Key Characteristics
High impact or impact modified
Recorded properties are for screening; verify source data and conditions.
Total 8647 materials | Scroll down for more